Skip to main content

 

How do I enable time synchronization of VMware Aria Automation


You can enable time synchronization on your VMware Aria Automation deployment by using the VMware Aria Automation appliance command line.

You can configure time synchronization for your standalone or clustered VMware Aria Automation deployment by using the Network Time Protocol (NTP) networking protocol. VMware Aria Automation supports two, mutually exclusive, NTP configurations:

NTP configurationDescription
ESXiThis configuration can be used when the ESXi server hosting the VMware Aria Automation is synchronized with an NTP server. If you are using a clustered deployment, all ESXi hosts must be synchronized with an NTP server. For more information about configuring NTP for ESXi, see KB article 57147 Configuring Network Time Protocol (NTP) on an ESXi host using the vSphere Web Client.
Note:If your VMware Aria Automation deployment is migrated to a ESXi host that is not synchronized to an NTP server, you can experience clock drift.
systemdThis configuration uses the systemd-timesyncd daemon to synchronize the clocks of your VMware Aria Automation deployment.
Note:By default, the systemd-timesyncd daemon is enabled, but configured with no NTP servers. If the VMware Aria Automation appliance uses a dynamic IP configuration, the appliance can use any NTP servers received by the DHCP protocol.

Procedure

  1. Log in to the VMware Aria Automation appliance command line as root.
  2. Enable NTP with ESXi.
    1. Run the vracli ntp esxi command.
    2. (Optional) To confirm the status of the NTP configuration, run the vracli ntp status command.

      You can also reset the NTP configuration to the default state by running the vracli ntp reset command.

  3. Enable NTP with systemd.
    1. Run the vracli ntp systemd --set FQDN_or_IP_of_NTP_server command.
      Note:You can add multiple systemd NTP servers by separating their network addresses with a comma. Each network address must be placed inside single quotation marks. For example, vracli ntp systemd --set 'ntp_address_1','ntp_address_2'.
    2. (Optional) To confirm the status of the NTP configuration, run the vracli ntp status command.

Results

You have enabled time synchronization for your VMware Aria Automation appliance deployment.

What to do next

The NTP configuration can fail if there is a time difference of above 10 minutes between the NTP server and the VMware Aria Automation deployment. To resolve this problem, reboot the VMware Aria Automation appliance.

Labels:

Comments

Post a Comment

Popular posts from this blog

Step-by-Step Explanation of Ballooning, Compression & Swapping in VMware

 ðŸ”¹ Step-by-Step Explanation of Ballooning, Compression & Swapping in VMware ⸻ 1️⃣ Memory Ballooning (vmmemctl) Ballooning is the first memory reclamation technique used when ESXi detects memory pressure. ➤ Step-by-Step: How Ballooning Works  1. VMware Tools installs the balloon driver (vmmemctl) inside the guest OS.  2. ESXi detects low free memory on the host.  3. ESXi inflates the balloon in selected VMs.  4. Balloon driver occupies guest memory, making the OS think RAM is full.  5. Guest OS frees idle / unused pages (because it believes memory is needed).  6. ESXi reclaims those freed pages and makes them available to other VMs. Why Ballooning Happens?  • Host free memory is very low.  • ESXi wants the VM to release unused pages before resorting to swapping. Example  • Host memory: 64 GB  • VMs used: 62 GB  • Free: 2 GB → ESXi triggers ballooning  • VM1 (8 GB RAM): Balloon inflates to 2 GB → OS frees 2 GB → ESXi re...
Post a Comment
Read more

ESXi Host Troubleshooting Checklist

  🛠️ ESXi Host Troubleshooting Checklist (With Complete Log Locations) ✅ 1. Host Status & Connectivity Check host state in vCenter (Connected / Not Responding / Disconnected) Review CPU, RAM, and datastore usage Validate HA/DRS recommendations ✅ 2. Hardware Health Monitor hardware sensors (CPU, DIMMs, fans, PSU, RAID) Check RAID controller logs via vendor tools View hardware status in: vCenter → Monitor → Hardware Health DCUI → Hardware Status ✅ 3. Network Validation Verify vSwitches, Port Groups, NIC teaming, VLAN tagging Check vmkernel ports (mgmt, vMotion, iSCSI, vSAN) Test reachability using: Shell vmkping < IP > Show more lines Validate physical NIC status and link speed ✅ 4. Storage & Datastore Checks Confirm datastore accessibility Rescan storage adapters (iSCSI/FC/NFS) Validate multipathing (Round Robin / Fixed / MRU) Check datastore latency with esxtop ✅ **5. Critical Logs & Their Locations (Full List) Here are key ESXi log files that every VMware adm...
Post a Comment
Read more
  vCenter Troubleshooting Tips, Common Issues & Log Locations 🚀 1. General Troubleshooting Approach A. Check service health first For vCenter Server Appliance (VCSA): Shell https : / / < vcenter - FQDN > : 5480 Show more lines Go to Services → Health to verify: vCenter Server ESXi hosts vSphere Client DNS, NTP, DB connections vpxd, vpxd-svcs, vsphere-ui B. DNS & NTP checks vCenter is highly dependent on correct DNS & time sync. Check: Shell nslookup < vcenter - fqdn > nslookup < esxi - host - fqdn > Show more lines Time drift > 5 minutes causes: Login failures vpxd crashes PSC authentication issues C. Check storage/database health Slow DB/storage = UI slow, tasks hung. For VCSA: Shell df - h du - sh / storage / log / * / var / log Show more lines Free up space if partitions hit >80%. D. Restart critical services safely On VCSA: Shell service - control - - status service - control - - stop - - all service - control - - start - - all ...
Post a Comment
Read more